How to Calculate Window Tint Visible Light Transmission (VLT)

Window tinting films are measured in visible light transmission levels (or VLT). This means that when we discuss a particular film, be it for fitting to a car or any other application, we normally refer to it with it’s VLT value. VLT is measured in percentage ( % ), so if you hear about a tint product being referred to as a percentage, it is the VLT that defines that percentage value.

For example, a tinting film referred to as Charcoal 5% is a charcoal coloured tint with a VLT of 5% and likewise a film referred to as green 50% is a green coloured tint film with a VLT of 50%. But what does the number actually mean?

Well, in simple terms the VLT value is the percentage of visible light that will be allowed to travel through the window tinting film from the exterior face side of the film to the interior side. This means that a 5% film will only allow 5% light travel through and a 70% film will allow 70% light to travel. In effect, this means that lower VLT films will appear darker. For instance, it is normally 5% tints that we will see on limousines for privacy.

So, fitting a 5% tint to a window will allow 5% light to travel through the glass from outside to inside, right? NO! Because we need to take into consideration the actual VLT of the window before the tint is even installed. There is no such thing as a piece of glass, no matter how clear it appears, with a VLT of 100%. This is because glass naturally filters out a little bit of visible light.

Lets look at car window tinting as this is one area where we speak of VLT often due to the fact that many countries have laws in place limiting how dark car windows should be tinted. Most modern cars come from factory with windows reading a VLT somewhere between 72% and 78%, depending on manufacturer, model and country. Say, our example car’s windows read at 72% and we add a 50% window tinting film, what is the new and final VLT of our car’s windows after installation?

The sum is very simple: V1 x V2 = V3 (Where V1 is the original VLT of the glass before tinting, V2 is the VLT of the window tinting film and V3 is the final VLT value of the glass with tint film applied).

Our car’s windows original VLT = 72% and the tint = 50 %, thus V1 = 72 and V2 = 50

The sum is 72 x 0.50 giving us 36, which we will express as a percentage. So a window with an original VLT of 72% will then have a VLT of 36% after application of a 50% film.

Motorcycle Components

In our daily life, motorcycles are also catch people’s attention except for cars and bicycles. They are important transportation mode that we can not ignore. Motorcycles have been developed a lot through these years. Modern types are quite different from the earlier ones for that they can include high-tech components.

It is common that every product should depend on various parts to achieve the expected function, so do the motorcycles. They also need specific parts to function properly. Different components work together to keep the motorcycles in a good condition.

One of the most obvious and important parts is the wheel. Generally, there are two wheels on a motorcycle which featured steel spokes traditionally. But through the development, many other types can be found now such as the cast aluminum wheels and other alloy models. Usually, rear wheels may be larger and wider than front wheels because of their drive configuration.

Drivetrain is just like the heart of the motorcycle. It is powered by the drivetrain which includes the engine. Motorcycle engines are usually centrally mounted below the driver’s seat. It conveys power to the rear drive wheel through its   transmission . The  transmission  itself is attached to the engine, and operated by a shift lever and a clutch. And the system connecting the  transmission  to the rear wheel (the final drive) varies on different types of motorcycles, and may be a chain or belt, or a solid shaft.

Brakes are also necessary components on a motorcycle. They are controlled by a hydraulic system that is activated by handlebar or foot levers. Typically, disc brakes are offered on high end models or heavier motorcycles that require more powerful brakes.

Electrical system is an indispensable part. Sometimes, it is very complex. Some of the most basic electrical components are the lights, which include the headlights, tail lights, directional signals and brake lights. In addition, the instrumentation which includes the speedometer, tachometer and odometer is also an important part of this system.

Of course, there are still many other parts which also have significance to the motorcycles. They may be added to distinguish one model from another, or to prepare a motorcycle for a certain type of driving. All in all, all of the motorcycle parts are important for the proper function of the whole machine.

How to Cure Ringworm?

Ringworm is a very contagious skin fungal infection. It can affect all individuals and even animals. During the infection stage of the ringworm, they produce fungal spores that can be transmitted to others. When you become exposed to fungal spores, you are at high risk to develop ringworm. But ringworms are treatable, and ringworm cures are very helpful to remove and kill fungal spores.

It is very essential to kill the fungi, and prevent the spread of ringworms to your body and to other people or animals. Here are some tips that will help you:

– Perform environmental disinfection regularly. It is important to maintain a clean environment because fungal spores can be present anywhere, especially to places where the infected person has been exposed to. Bleach is common in every household, and is very effective in disinfecting the environment. You just need to make a 1:10 bleach and water solution, and use it in decontamination of floors and surfaces. This will effectively kill the fungal spores, and prevent its transmission.

– Use a vacuum with HEPA filters. High Efficiency Particulate Absorbing or Arrestance (HEPA) filter removes at least 99.97% of airborne particles such as dust and fungi. It is very useful in cleaning carpets and upholstered furniture to remove fungal spores.

– Isolate infected pets. It is very important to separate your infected pet from other animals. You should not touch or come in contact with the infected pet because you can contract the fungal spores that cause ringworm. Consult your pet’s veterinarian so that you can determine what type of treatment will help your pet resolve its ringworm.

– Do not share personal articles. Sharing is a good act but if you have ringworms, it is a big no to share your personal items to others. Your things are contaminated with fungal spores. You should keep them and disinfect them using bleach.

– Keep a clean body. Fungi flourish in dirty areas. Proper personal hygiene should be observed to prevent the spread of ringworm on your skin. It is also important to perform regular hand washing after treating your ringworm, and after touching or treating your infected pet because you can obtain fungi spores from it.

– Maintain a sweat-free body and wear comfortable clothing. Fungi thrive in hot and moist areas of your body such as armpits, groins, and areas which have folds especially to obese individuals. You should keep yourself dry and avoid wearing tight clothes.

– Use a natural ringworm remedy. Natural ringworm remedies are found to be effective against ringworm, and they are absolutely safe to use. They are medicinal herbs that use leaves or extracted oil to cure ringworm such as turmeric (Curcuma longa), coconut oil (Cocos nucifera), mustard seeds (Brassica nigra),cassia leaves (Cassia fistula), holy basil leaves (Ocimum sanctum), butea seeds (Butea monosperma), and papaya seeds (Carica papaya). They are applied directly over the ringworm patch. Carrot (Daucus carota) and spinach juice (Spinacea oleracea) are also helpful in treating ringworm because they contain large amount of beta-carotene, which are very good for skin care.

– Apply topical creams. Topical creams are effective for ringworms that have mild symptoms. They are over-the-counter medications that help to relieve ringworm symptoms and kill fungi that cause ringworms. Topical treatment should be used for 2 to 4 weeks to effectively eradicate the fungi. Topical medications include Miconazole (Micatin, Desenex, Daktarin, Monistat-Derm, and Decocort), Clotrimazole (Mycelex and Lotrimin), and Terbinafine (Lamisil AT, Lamisil, and Lamisil Dermgel).

– Administer anti-fungal pills. Anti-fungal pills are systemic treatment for severe cases of ringworm. It is recommended to consult your physician so that you will be advised on the proper dosage and length of treatment using oral anti-fungal medications. Anti-fungal pills include Griseofulvin (Gris-PEG, Grifulvin V, Fulvicin P/G, and Griseofulicin), Itraconazole (Sporanox and Sporanox PulsePak), Terbinafine (Lamisil), and Fluconazole (Diflucan).

The First Steps Towards Becoming A Working Actor

So your bags are packed and your next destination is Hollywood to pursue your life long dream of becoming a movie star. No one will say its an easy road to take, so hats off to you for going through with this journey. This article will save you a lot of time in preparation when you make it there. The first thing you need to do is land an agent. Listed below are the four main things you need to have/do in order to get that agent.

ACTING CLASSES

Before an actor becomes an actor, they are put in training. The same way a boxer conditions his or her body to become a better fighter, an actor trains through acting classes, to hone his or her craft.

Acting classes are the basics, where you start before anything else if your desire is to become an actor. You develop your skills using various techniques to mentally train your mind to transform yourself as a person saying words written on paper, into a person living in a moment of truth. There is no single method or technique that is correct; it’s all about finding the approach that works for you. Again, just like every boxer has a unique style, every actor brings something different to the table. Whether you identify with Sanford Meisner, Constantin Stanislavski, Lee Strasberg, Stella Adler, or somebody entirely different, a great acting program will offer one or a combination of the techniques that work for you.

HEADSHOTS

The first thing an agent or casting director look at (whether finding new talent or filling a role) is a headshot.

A headshot is an accurate picture of you, representing your physical attributes. A headshot photo is often of one’s face, but just as fashion trends come and go, headshot framing can be trendy as well. Another great reason to have a current photo, is so that you don’t seem outdated in terms of style, color, and formatting. A person’s entire body can be used in a headshot when submitting to a modeling agency.

A “look” is an actor’s demeanor in a photo. If an actor wishes to audition primarily for comedic roles, the photographer will direct him into a playful mood, capturing images of the actor smiling, and perhaps looking a bit goofy. For action roles, the demeanor could be more intense and serious. This is not necessarily a rule, but rather a way of creating an advantage for those going after specific roles.

When just beginning a career, it is crucial to have a variety of photos to demonstrate versatility and to open up as many doors as possible. Don’t pigeon-hole yourself right away, but at the same time, be honest with yourself. Know what you can and can’t do as an actor and get pictures that correlate with your repertoire of skills.

At the very least, an actor just starting out needs a commercial shot (generally a smiley picture used for commercial auditions) and a theatrical shot (generally more serious, used for film and television auditions).

ACTING RESUME

An actor’s resume displays the work they have done. A rule of thumb in the industry is to have your resume stapled at the corners and behind your headshot, making a clean attachment for casting directors and agents who sift through hundreds of headshots, looking for that person with the right look for a particular role. Although almost all submissions are digital these days, having hard copies of your picture and resume is still expected.

Your resume should consist of only the most the basic info: your name and contact information (either personal phone number and/or email address, or that of your agent/manager). If you belong to SAG-AFTRA you should indicate that as well. Putting your height, weight, and hair/eye color used to be standard, but has begun to phase out.

List the most prominent productions you have been involved in, and the details should be broken down into different headings: Film & TV, Theater and New Media (web series). Once your credits begin to grow, the heading of Film and TV can be broken up into two categories. Next you should list your training. Acting classes, theatre, voice over training, etc.

Lastly, the most commonly overlooked section of a resume: Special Skills. Here is where you can brag about hidden talents you have, or cash in on ordinary talents. List the sports you play, the games you know, the accents you can do, the languages you speak, etc… You’d be surprised how many actors can book a role simply because they know how to hula hoop or, believe it or not, drive a manual transmission. You can also use this section to be creative and write something that will stand out and make you memorable. If you can freestyle rap, for example, that’s a great way to grab attention on a resume, just be prepared to show it off if and when you’re asked about it. DO NOT LIE on you Special Skills section. It will only hurt you in the long run.

Now here’s the catch 22. You need an agent to get work, but you can’t get work without an agent. So how do you get work without an agent to start? I’ve been in this predicament, and had an agent call me and tell me this exact bit of information.

“A good agent won’t represent somebody who doesn’t have an acting background, even if you found one that did, you don’t want that type of agent representing you. You need to focus on building your resume. Get enrolled in some acting classes, and for work, try looking into either Craigslist to get involved in any student films, or lacasting.com and do some extra work. All of this will help build your resume and show you are serious about acting.”

DEMO REEL

After you feel you’ve taken enough acting classes, had your headshots taken, it’s time to start looking for representation. It’s very difficult getting represented by an agent with just your headshots, resume and acting training. You need a video montage of you showing off your acting chops. This where a demo reel comes in handy.

A demo reel is a collection of scenes edited together to showcase the ability of an actor. Demo reels are also made for directors, cinematographers and editors as well. For an actor, a demo reel can be used to show their genre range, mixing in various works they have done from dramatic to comedic. They can also be tailored to represent an actor in one complete genre, such as an all action genre reel. This usually comes only after the actor has enough credits to warrant separate reels.

A good demo reel is usually between three to five minutes in length and displays anywhere from six to eight scenes. Sizzle reels, are a trimmed down version of a demo reel, usually running no more than one minute in length with music overlaying the edited footage giving a “teaser” type effect. Sizzle reels are becoming quite popular, as they are quick and stylish. It is good to have both, as every agent has their own reservation for what they want submitted.

The biggest mistake people make in getting their demo reel made is that they over do it. Often times I’ve seen demo reels consisting of scenes of a person screaming at the top of their lungs or crying, or holding a gun and shooting someone. A great demo reel should be 2 things, subtle and entertaining. Keep that in mind. And always lead with your best stuff, either your most impressive credit, or the clip(s) that showcase you the best. Remember, the person watching the reel doesn’t love you as much as you might love yourself, and isn’t likely to watch the entire thing, no matter how short it is.

TIME TO GET AN AGENT

At the end of it all, you’ve got enough acting classes under your belt, you have a great new headshot, your resume is substantial and growing, and you have a reel that represents you well, it is now time for you to find an agent. You can check out our updated Agent list. We hope this article has been a good source of information to you. Check out our site for other articles related to the world of acting. Good luck on your journey, looking forward to seeing you on the silver screen!

Knowing Reiki Massage

Reiki massage is a form of energy healing treatment that sends out energy and is directed into the chakra points. It is completely harmless and safe to use because it does not involve heavy skin to skin contact or massage.

Reiki massage is the treatment wherein spiritual energy is used and goes directly through the body’s chakra points. It incorporates healing in varying aspects of the recipient and may have little or no skin-to-skin contact. The word “reiki” is a Japanese kanji or Japanese words that are put together. Rei means “universal spirit” and ki means “life energy” and reiki means “universal life energy”. Massage is the process wherein the therapist rubs different parts of the body for an invigorating and refreshing feeling. Some therapists that are trained in massaging and also took Reiki attunement classes are called Reiki therapists and sometimes they use reiki and massage altogether to provide the maximum health benefits the recipient can get.

This massage is expected to have positive results such as providing pain relief and overall physical, mental, emotional or spiritual wellness. Commonly, this massage does not incorporate skin contact from the practitioner to the recipient, but the practitioner’s hand remains still and transmits reiki energy into the recipient’s body, which is spiritually guided and gives healing results. It is believed to treat muscle pain, any form of injury, tension, TMJ (also known as lock-jaw), stress and so much more.

The Reiki massage can be used in two different ways.

Healing from a distance

The recipient is advised to go to a relaxing place of their choice or set up a comfortable place inside their house where they will not be disturbed from any event in and outside their home. The practitioner will start the treatment and transmit Reiki energies from their body to the recipient. This all happens from a distance.

In-person healing

This form of healing is used when the practitioner is present and can interact physically with the recipient. The recipient is advised to lie on a mat or preferably a massage table and not advised to be naked. It is important to be completely comfortable and open to the healing energy one will receive during treatment. The treatment area should be relaxing; put aromatherapy scents around the room, play soothing music, etc. just to place the recipient in a relaxed state. The practitioner transmits reiki energies from their hands to the recipient’s body by gently touching different parts of the body.

The beauty of Reiki massage is that everybody can enjoy them but everybody can learn how to give them as well.

Genital Herpes Symptoms and Treatment

Genital herpes is one of the most common sexually transmitted diseases in the world today. It is caused by the herpes simplex virus.  This is the family of viruses that causes cold sores, shingles, and chicken pox. 

Genital herpes is caused by infection with the herpes simplex2 virus (HSV2). HSV1 is the virus that causes cold sores on the lips and nose area. The herpes virus, however, is not too particular about the mucous membrane it calls home and will happily live in either the mucous membranes of the mouth and lip area or the reproductive tract.  Because of this, oral genital contact can spread either HSV1, HSV2. Viral transmission can occur from the mouth to the genitals or from the genitals to the mouth. The blister type lesions caused by either virus are virtually identical.

Genital Herpes Symptoms

Sometimes after the initial infection there may be fever and general malaise as could be seen with any acute viral infection but this is not always apparent in all cases.  In fact the symptoms of a genital herpes infection may not be known to you until you see some blisters on or around your genital area. 

This is called an outbreak and is characteristic of the way the herpes virus acts in the body. There will be periods when the virus is dormant and none of the characteristic symptoms of genital herpes are present.  Then there will be these outbreak periods where blisters appear in the genital area and may even extend to the anal area. 

The blisters will act like any normal cold sore on the lips.  They come up with an initial tingling, then grow larger and spread and eventually burst leaving an ulceration that will slowly heal on its own.

In men these blisters occur on or around the penis.  In women the blisters may actually be in the vagina as well as on the surrounding genital area. 

Symptoms of genital herpes will come and go but the virus stays with you forever. The number of outbreaks will gradually become less and less and in some cases, some people do not see outbreaks at all.   

Diagnosis

You may not know you have contracted genital herpes until the first breakout of the blisters. Symptoms of genital herpes are so mild in some people they think they just have a skin irritation.  The best thing to do is to be checked by a doctor so that you can get diagnosed properly. 

Doctors can usually make the diagnosis based on inspection of the genital area as the lesions are quite specific in appearance.  In some instances the doctor may take a swab on the blister fluid to see if it contains the virus.

Genital Herpes Treatment

There is no cure for genital herpes, however, it can be controlled so that you can live a normal sexually active life.  Anti-viral medications are often prescribed at the first outbreak to knock back the infection and may be used for prolonged periods if outbreaks are frequent.

Other treatments for the discomfort of an outbreak are common sense measures such as wearing loose comfortable clothing, using cold compresses or soothing creams and ointments on the blisters.

A strong and healthy immune system is needed to keep the virus suppressed and to reduce the frequency of outbreaks. Health denying habits such as smoking, drug use, or toxic relationships will drain the resources of your immune system so your best method of treatment is to maintain good health.  This would include eating whole nourishing foods, getting plenty of exercise, and managing stress. 

Complications

Generally the herpes simplex virus is not considered a dangerous infection to persons who have a fully functioning immune system. The virus will be suppressed and outbreaks will not be common as long as the immune system is functioning well.

However, if the immune system becomes burdened or compromised in any way then outbreaks will be more likely to occur.  This may happen during times of physical or emotional stress.  If the immune system is comprised by other more serious illnesses such as HIV or cancer then the herpes virus can become more dangerous.

If the virus is directly transmitted to other areas such as the eyes, or the brain, complications can be very serious. This direct transmission can happen in a number of ways but the most common is during the birth process.  The infant can become infected with the virus from contact with the mother’s vagina during birth.

If you suspect you may have contracted a genital herpes infection see your doctor as soon as possible.  Never have sex during an outbreak and never have unprotected sex. This means using a condom  (either male or female type)  during every sexual encounter even during oral sex. 

Additionally you should always inform your partner of your herpes status.  This is always the right thing to do.

How to Program a Siemens S7-300 Programmable Logic Controller

Do you have a Siemens S7-300 Programmable Logic Controller that you are not familiar with but you need to program it NOW! Following is a quick set of instructions I have put together to help you get started programming a Siemens S7-300 PLC.

After loading the programming software and connecting a Siemens MPI cable between your programming computer and the PLC, open SIMATIC Manager by clicking the icon on the desktop. The STEP 7 Wizard: “New Project” window will open. It is easier to use the Wizard to setup communications with your PLC, but I chose to take the scenic route. I figured I would learn more this way. So, close the STEP 7 Wizard window by clicking Cancel. If there are any other windows or projects open, close them. We want to start with a totally new program.

Create a new project by clicking the new project button on the toolbar in the upper left corner of your screen.

The New Project window opens. Here you will see any existing programs located on your computer. Near the bottom of the window, you will see the Name: input form. Type whatever you want to name your new project and click OK.

A new window will open showing the name of your project at the top. You will also see your project in the window on the left hand side of the screen at the top. Right click your project and choose “Insert New Object”. Choose the device you will be programming. We will be using the SIMATIC 300 Station so choose that selection.

You will now see SIMATIC 300 appear in the right window of your screen. It should be highlighted blue. Click anywhere in the window to make the blue go away. Double click SIMATIC 300 and it will move to the left window and “Hardware” will appear in the right window.

Double click “Hardware” and two (maybe three) new windows will open. On the left will be SIMATIC 300 – (the name of your project). The window on the right will be the catalog of parts.

Look in the right window, the parts catalog, and click the plus sign beside SIMATIC 300.

Click the plus sign beside RACK – 300. Click and drag the Rail onto the left window. You will now see the Slots window appear. This is where we will place our PLC components.

We will first choose our CPU. Looking at the parts catalog, in the SIMATIC 300 tree, choose the CPU that you are using. We are using the CPU – 300 so click the plus sign beside that choice.

Now look at the front top left of your PLC. This is where you will find the PLC model. I will use CPU313C-2 DP as an example since this is the model PLC that I use.

Find this CPU in your parts catalog and click the plus sign. You will now see some part numbers.

Look back at your PLC. Locate the door covering the MPI port. This will be the bottom left side of the PLC. At the bottom of the door you will find the part number. The part number for the PLC I am using as an example is 313-6CF03-0AB0.

Find this part number in the parts catalog. You will notice this is another folder. Open it and you will see V2.0 and V2.6. Look back at the PLC, open the door covering the MPI port, and right above the MPI port you will see V2.6.3.

Go back to the parts catalog and click V2.6. Notice how a slot in the left hand window will highlight green. I believe it will be slot #2. (Slot #1 is reserved for power supplies.) This is where you will drag and drop your CPU. (Notice the software will not let you put the CPU in any other slot but slot #2.)

When you release the mouse button over slot #2, a new window will open, “Properties – PROFIBUS interface”. Click new, a new window opens, click Ok, and then click OK again. We are not setting up a network at this time.

You will now see your CPU and associated hardware listed.

Double click in the Slot that list your DI16/DO16 (Digital Input/Digital Output).

A window with three tabs will open. The first tab will be General, the second tab will be Addresses and the third tab will be Inputs.

Open the tab “Addresses”. We need to change the default addresses. Do this by unchecking the System Default button and changing 124 (or whatever address you have) to 0. Do this for both the Inputs and Outputs.

We now need to change the Node Address. Go back to the window where you double clicked DI16/DO16 and double click in Slot 2, the CPU 313-2DP slot.

The Properties – CPU 313C-2DP window will open.

Look down the window a little over half way and find the Interface area and click on Properties. Another window, “Properties – MPI interface CPU 313-2DP” will open.

Change the address to meet your specific criteria. I know that my laptop, which I am using to program my PLC, is always addressed as 1 and my target PLC is usually addressed as 2. You will probably be the same.

Now click MPI(1) and click OK. Click OK again to close the Properties window.

Save and Compile by clicking the icon located on the left of the toolbar.

Download the hardware configuration to the PLC by clicking the download icon located on the toolbar.

A window titled “Select Target Module” should open. Click OK.

Another window titled “Select Node Address” will open. You should see listed your node address for the PLC you are working with as you configured it in a previous step. If not, click view and click on whatever node address appears and click OK.

Switch back to SIMATIC manager (by clicking the tab on the taskbar).

Click on Options. Choose Set PG/PC Interface. Choose PC Adapter (Auto).

Click Properties. A new window will open, displaying either Automatic Bus Profile Detection or Local Connection. Click Local Connection and choose USB. Now choose Automatic Bus Profile Detection and change the address to 30. You can check your connection now by clicking Start Network Detection. If a new window opens displaying Network Type = MPI, Transmission Rate = 187.5kbps, you have established communications with your S7-300. Click Close. Click OK. Click OK.

It is now time to start programming. Looking at the SIMATIC Manager window, click the plus sign located beside SIMATIC 300(1), click the plus sign beside CPU 313C-2DP, click the plus sign beside S7 Program(1). Now click on Blocks and you will see System data and OB1 appear in the right window on your screen.

Double click on OB1 and a new window will open named Properties – Organization Block

Here you can choose how you want to program, in LAD (ladder), STL (statement list), or FBD (function block diagram). Choose which you want to use and click OK.

Double click OB1 again and the LAD/STL/FBD programming window will open.

You can now start programming.

I have these same instructions with pictures on my website at http://www.saturdayafternoonhobbies.com

Everything You Ever Wanted To Know About Condoms

If there was ever an invention to make sex as safe as possible, it has to be the condom. Not only do they prevent the spread of sexually transmitted diseases, but they’re very effective at preventing pregnancy too. No other form of contraception is so reliable and versatile. So what’s not to love?

Buying them

So you’re shy about asking for them? Supermarkets and gas stations carry condoms these days – you can buy them from a machine in the washroom. Sex clinics give them out by the handful for nothing. And if you still feel weird about getting your hands on condoms – just consider how it would feel buying medicine to treat an STD instead.

Carrying them

Is it presuming too much to take condoms on a date? Frankly, that attitude hasn’t been seen since the fifties. So the girl might realise you do have sex and you wanted it with her. Is that an insult? In any case, you don’t have to take them out your pocket and wave them around. If you get to the point where you need one, you’ll both be happy to see that little foil wrapper, never mind who was carrying it!

Using them

Remember the classes where you practised with a banana? Do yourself a favor, practise with the real thing. Use a whole pack if you need to – keep trying till you know how to get one on properly. You won’t be able to put on a condom if your penis isn’t fully erect – but remember that the penis releases fluid that can spread STIs or contain sperm even before it’s erect. Remember to pinch the ‘teat’ at the end before you unroll the condom down your penis – you might want to leave a bit more space at the top to prevent the condom from splitting. Keep this teat pinched between your fingers as you unroll the condom, and make sure it’s fully covering your penis before and during sex. Don’t feel shy about interrupting your lovemaking to put one on – that pause can only build the excitement!

Last words

Oil based lubes, sharp fingernails, jewellery and out of date condoms are all recipes for disaster. Use a special lubricant. Some people find they have an allergy to latex – condoms now come in allergy-friendly latex-free varieties. In fact, there are now a vast number of different shapes, colors, sizes and flavors of condom. Experiment to see which ones you and your lover prefer – perhaps a ribbed variety for more stimulation or a condom with extra lube for very sensual sex. You should use a condom or dental dam for oral sex too, and change condoms for every new orifice or sex act.

Finally, to get rid of a condom, wrap it and bin it. Never flush a condom down the toilet.

For more information about lingerie please have a look at this link:Exotic Lingerie | Blouses See Thru [http://www.oasislingerie.com]

Motorcycle Automatic Transmission – The Top 3

Motorcycle enthusiasts love a wild goose chase such as the famously beloved, Bigfoot. Many motorcyclists fail to believe that there is actual automatic transmission motorcycles that exist. This is not true because the knowledge isn’t out there. This is actually true because of there just aren’t to many readily available. The top three automatic transmission motorcycles really exist and the proof is found by reading on.

3. The Honda DN-01

The Honda DN-01 was introduced in 2005 as a cruiser motorcycle. This is one of the first of very few automatic transmission motorcycles ever released. The bike didn’t actually make it on showroom floors until 2008-2009. This bike is so powerful to the consumer that it is still being offered in shops as of early 2011. Missing you chance to check out the Honda DN-01 is just wrong. The Honda DN-01 is just one of those bikes you can’t miss a chance to try out for yourself.

2. The Aprilia Mana 850

The Aprilia Mana is a newer automatic transmission motorcycle that was just released last year. This bike is fast and very powerful. The Aprilia Mana 850 is a sleek sports bike that offers highlights from leather to chrome and everything in between. There is nothing better than a quick bike with the backing of being an automatic transmission motorcycle. The Aprilia Mana 800 makes its way to this top three list for being a solid bike with an even nicer ride.

1. The Honda CB750

The Honda CB750 has had many models in its series between 1969-2003. The Honda CB750 automatic transmission models is better known as the Honda CB750 Hondamatic. This model is one of a kind that has a coil ignition start and a solid inline four stroke SOHC air cooled engine. The only downfall to this model was the fact that the gear changing was not automatic. Instead, each gear was chosen by a foot-controlled hydraulic valve. This bike only sold in the North American market but can now be found all over the world.

STD Symptoms in Men

Sexually transmitted diseases (STDs) in men are just as common in men as are in women. The difference is that some of these STDs are not as easily detectable in men. They can be cured through medication or through simple surgery and recurrences of the disease are unlikely. Because it is difficult to detect certain STDs in men it is advised that he gets checked on a yearly basis to ensure that he is in good health and that there are no diseases hiding within his system. This way he can get tested for STDs and begin treatment immediately.

Chlamydia

Chlamydia is one of the more common STDs a man can experience. It develops through contracting microbes called Chlamydia trachomatis. As per the Center for Disease Control (CDC), Chlamydia is the most common STD in the United States. Between 2004 and 2008, the rate of Chlamydia reported increased to 45 percent due to the advancements in STD testing methods and over the counter testing methods such as home STD testing kits. Chlamydia can typically be detected within one to three weeks after symptoms are presented.

Men infected with the disease will experience discharge from the penis, painful urination, and a burning or tingling feeling around the opening of the penis which can also be felt in the testicles. If Chlamydia is found in the rectal area, men will experience symptoms such as rectal discharge or draining and severe pain both during bowel movements and random times throughout the day if not all day. Additionally, Chlamydia can be transmitted to the throat through oral sex.

Gonorrhea

Gonorrhea is developed through contracting specific microorganisms called neisseria gonorrhoeae. Symptoms of gonorrhea include painful urination, white, yellow or green discharge from the penis, and swollen or enlarged testicles. Gonorrhea also affects the rectum and can be extremely painful. Symptoms a man could experience include rectal discharge, soreness, tingling sensations, rectal draining, and painful, hard, solid bowel movements. If gonorrhea has been contracted via oral sex, a man will experience a sore throat that will continue to get worse due to the many different types of bacteria already in the throat interacting with those microorganisms that cause gonorrhea. Gonorrhea can also cause epididymitis which is the curved portion at the back of the testicles where sperm matures; it is the swelling of the tube that connects the testicle to the vas deferens. Side effects can take anywhere from two to thirty days after contracting the disease. If left untreated, it can leave a man infertile and unable to have children.

Syphilis

Syphilis is one of those “silent but deadly” STDs. You could have syphilis for several weeks, months, and in rare occasions, years before experiencing side effects in any stage. The first phase of syphilis presents itself as sores around the genital area. This type of sore is called a chancre sore. It will appear as a hard, indented portion on your skin and typically disappears without treatment within three to six weeks. The second phase of syphilis rears in the form of a rash on the skin and mucous layers in the body. The rash could be extremely red and harsh or as tan spots that are most commonly found on the palms of the hands or the soles of the feet. Other symptoms you may experience include swollen lymph nodes, fever, sore throat, cerebral pain, random male pattern baldness, significant decrease in weight, and being unusually fatigued or exhausted. The rash is the biggest indicator of how severe the disease is; while it will go away on its own without treatment, once it goes away it serves as the primary indicator that the disease is now in the advanced stages. In the late stages of syphilis, a man will not show any visible side effects. However, while side effects may not be visible, the disease will essentially “eat away” and attack the major organs. In this stage, the disease begins to attack the brain, heart, liver, bones, and joints. A man can experience loss of motion, numbness, changes in vision to the point where he may eventually become blind, dementia, and the inevitable, death.

Herpes

Herpes is the most common form of STDs. It develops by contracting the herpes simplex infection 1 (Hsv-1) or herpes simplex infection 2 (Hsv-2). However, genital herpes is most commonly developed by contracting the Hsv-2 virus. The herpes virus first presents itself as one or more rankles in the genital or rectal areas of the body. These are open sores that turn into ulcers on the genitalia and rectum and can take a man five or more weeks to get rid of the virus. When the flare up is first noticed, it is the most painful, the most intense, and the most excruciating pain a man will experience. As time goes on, these episodes are less successive and less uncomfortable.

Human Immunodeficiency Virus

Human Immunodeficiency Virus, or HIV, attacks the immune system leaving a man extremely vulnerable to catching other severe illnesses. Most times when a man who has contracted the HIV virus, he may experience no symptoms of the disease. It isn’t until he becomes ill with another type of illness that HIV is detected. Flu-like symptoms such as a fever, sore throat, and swollen lymph nodes can begin to rear two to six weeks after being infected with the HIV virus. Other very common symptoms of traditional illnesses that are often seen with HIV include diarrhea, unexplained weakness, mouth sores, and a rash. These symptoms may take 10 years or more to even appear if the typical flu-like symptoms don’t appear. Having additional STDs can increase your chances of contracting the HIV virus.

Testing for STDs

Getting STD testing is more accessible than it used to be. Now, you can walk into any pharmacy and buy an STD at home testing kit which will detect certain types of STDs but not all. Testing at home has become the more common method of testing to avoid the embarrassment factor of going to their doctor. If a man suspects he has contracted a more advanced STD than what a home testing kit can detect, it is imperative he be tested as soon as possible by his doctor so the disease can be treated promptly. With home STD testing kits, a man can obtain his test results online and can take those results with him to his doctor to begin a treatment regimen for the disease. If needed, additional testing will be done to pinpoint the exact STD he has contracted.